Re: How best proceed with overheating i7-4790K?
Hi! By unstability I meant BSOD What can I do in that case?
View ArticleNot able to read "/dev/ttyMFD1" using serialport module in Intel XDK
Hi community, I am trying to read the data sent by my Ardunio IDE to pin "0" of Galileo . In the edison console , i am able to see the correct data sent using the command "cat /dev/ttyMFD1".But if i am...
View ArticleRe: How best proceed with overheating i7-4790K?
Exactly. I agree with what Woolphy said. slaveonepunx, what you are saying is that something may be wrong with our processors because it isn't going anywhere near the max TDP of 88W, especially with...
View ArticleClik here to view.
Re: How best proceed with overheating i7-4790K?
Do you remember what the BSOD code was? If you were at stock settings, resetting CMOS and then putting everything to auto SHOULD take care of everything, depending on your board. In your case, if...
View ArticleMRAA not working/ Sys gpio does
So I've finally gotten to the point with edison yocto that it doesn't seg fault on my edison/mini breakout when using MRAA, but nothing happens either. However, manually driving the gpio through...
View ArticleRe: Intel Update Manager
Thank youfor your answer.I donot haveto install theWindows8.Windows8installationmediaalso, It doesnot use, I do not have.However, sometime, by a pluralityofPCofmycompany, "Intel Update Manager" is, are...
View ArticleRe: Intel Update Manager
Versionofthe updateof theIntelgraphicsdriverdoesnot conduct.AndWhatbugIntelHDgraphics?Wouldthereisfunctionto stop?
View ArticleRe: DH87MC system start problem
can you try this and let me know !don't switch on or use the computer for a day, almost 24 hours, switch on the next day, and let me know if it works fine. i salute your efforts but let me know the...
View ArticleRe: NUC DN2820FYKH: WARNING: Processor thermal trip at boot
Thanks Lois Version 0043 worked better no "thermal tripping error" after about 8 reboots, fingers crossed
View ArticleRe: Get SMART info from ICH10r raid controller(onboard)?
Ok. As far as we have seen we can use this tool in Command prompt.Is there a way to use this tool from for example a C# application and get the values we want directly? For example, if we wanted...
View ArticleRe: is WPA2 supported on Galileo Gen2 Yocto image?
Hi, wpa2 is 802.11i but not 802.1x I'd say. So not quite sure what you really are looking for.In general I tend to use connman as described on IoT - Connecting Intel(R) Edison to an IEEE 802.1x...
View ArticleRe: regression in mraa for ww42 image
deium wrote: mhahn,That leaves a question, how do we reverse the update?opkg remove --force-depends libmraa0wget http://iotdk.intel.com/repos/1.1/intelgalactic/libmraa0_0.5.3.7_i586.ipkopkg install...
View ArticleRe: MRAA not working/ Sys gpio does
Can anyone with working mraa (through node) elaborate on: firmware version and download linkany opkg requirement to update mraa, build pls check https://communities.intel.com/message/268027#268027
View ArticleClik here to view.
Re: mraa: Illegal arguments for construction of _exports_Gpio
for now pls revert to libmraa v0.5.3.7 for the steps pls check https://communities.intel.com/message/268027#268027
View ArticleRe: Unable to update Edison
if you don't need permanent journal then you may also set volatile in journald.conf (see other threads on that) deium "systemctl disable edison_config" would do as well. No need to type the trailing...
View ArticleRe: Какой процессор выбрать для апгрейда?
Felis_83, just in case microcode is used in CPUs. It contains the latest microcode definitions for all Intel processors. We releases microcode updates to correct processor behavior as documented in the...
View ArticleRe: Servo trouble
Hello Stephen.Schieberl, Why you try setting your output pins with low-impedance using pinMode()? Please tell me if this this makes any change.Also could display the output of the servos pins with an...
View ArticleRe: Webcam throwing distorted Images
Thanks for your response. This is the code im using. I would be glad to know if its the problem with code or driver. And deium can you pls tell me how to get corrected image as you did. int main(){...
View ArticleUSB 3 drives won't power down
USB 3 drives won't power down even with Power Option, USB Selective Suspend, enabled. Same USB 3 drives, Seagate and Toshiba, power down on other machines, but not on NUC, D54250WYK, 8.1 Windows Media...
View Article