Re: Your computer does not meet the minimum requirement for installing the...
Kevin,Help please!I have installed Windows 7 Ultimate 32 on my new Asus X553M and I have successfully installed all drivers except Intel HD graphics.I am getting "The computer does not meet the minimum...
View ArticleCannot install Intel HD graphics driver on X553M Windows 7 - 32
Help please!I have installed Windows 7 Ultimate 32 on my new Asus X553M and I have successfully installed all drivers except Intel HD graphics.I am getting "The computer does not meet the minimum...
View ArticleRe: How to enable PIN0/PIN1 for UART usage (TX/RX)
gzyulin,From the Edison Arduino Guide: There are two UARTs available, UART1 with flow control and UART2 without flow control. The UART1 interface is available on DIG0 and DIG1 pins. UART2 is connected...
View ArticleRe: How to enable PIN0/PIN1 for UART usage (TX/RX)
Instead of some magic twiddling I'd recommend using this:mraa: uart.h File Referencemraa_uart_context uart;uart = mraa_uart_init(0); Job done. And it'll work on other boards like galileo etc
View ArticleRe: I2C with Edison Breakout board
The issue you are seeing likely relates to the fact edison only delivers 3mA on all IO pins. Likely your i2c sensor doesn't quite follow the spec and so is causing issues. We've had more success at...
View ArticleRe: Python HC-SR04 Sonar Setup
Welcome to the world of linux & linux userspace programming . We cannot guaraantee how long delays will be. Sadly the HC-SR04 and similar sensors typically won't work like this.
View ArticleRe: Intel i350 NIC Teaming Question
Hi MattJH, have you tried using VMLB teaming mode of Intel on your setup? kindly refer to the site below for details. Network Connectivity — FAQs: VMDq, VLANs, and Teaming on Intel® Ethernet Adapters...
View ArticleRe: Locating a Laptop shell that will house the Intel NUC
Not that Boldstripe. I want a shell of a laptop (housing+screen+battery) so I can stick the NUC into and it can be a portable AIO with a 15" screen so that the NUC is the system and there is some...
View ArticleRe: ttyS1 jack connector not work well all the time
I have already resolved the problem,my USB-RS232 conversor had a problem sorry Regards DF
View ArticleClik here to view.
Re: scp: /sketch/sketch.elf: No space left on device
Update: I found "/var/log/journal" took up 143.1M space! After deleting the directory, I got enough space to transfer sketch. Here is the space available now: Filesystem Size Used...
View ArticleRe: Debian Wheezy with Intel I350-T2 bonding issue
Actually I'm more interested in fixing the iproute2 functionality to disable anti spoofing completely Any news on that? https://communities.intel.com/message/192668#192668 - here Patric says Intel is...
View ArticleRe: glReadPixels fails when reading from a buffer other than the main windows...
John, As you mentioned, this is the same issue so we can continue on the other thread. Our development team is working on this one. glReadPixels not working when reading from a FrameBuffer Kevin M
View ArticleRe: SSH to my edison?
you probably will have to comment "BindToDevice=usb0" in sshd.socket which would allow ssh not only via USB0 # cat /lib/systemd/system/sshd.socket [Unit] Conflicts=sshd.service [Socket]...
View ArticleRe: Win 7 installation issue on d54250wykh
Have the same problem on my D4250WYKH with G.Skill Ripjaws F3-1866C10D-8GRSL 2 x 4 GB, i know that mine is 1866mhz but have the exact same problem, tested both memory modules in both sockets separately...
View ArticleClik here to view.
Re: How best proceed with overheating i7-4790K?
Hello abcanw! I think i could use your hel here. I have the sam mobo as you do ( GB z97x Gaming 5 with BIOS version F5 ). I was following this thread, and I did reset the default optimized setting in...
View ArticleHow can I upgrade BSP 1.0.1 to 1.0.4 about Intel Quark?
Hi IntelHow can I upgrade BSP 1.0.1 to 1.0.4 about Intel Quark x1000?I want to upgrade form 1.0.1 to 1.0.4.I try to download "BSP-Patches-and-Build_Instructions.1.0.4".The patch file line 33...
View ArticlePower up NUC when power is plugged into the NUC
I have two NUC D54250WYK and I want them to start up when the power is plugged into the wall. So I do not have to press the power button. Is that possible to do from bios?
View ArticleClik here to view.
Re: SSH to my edison?
It is already commented. This issue is caused by network I guess, since I can ssh if I connect edison to my cell phone (tethering).
View Article